VEGA Manual

1 Basics

1.1 Before starting

Before using, use the product safely after reading the user manual and safety precautions.

• The user manual describes based on the default setting values.
• The contents of the user manual may differ from the actual contents depending on the software version or model.
• Some services require an internet connection.
• If the user arbitrarily modifies the operating system or software, the product may not work properly. Also, warranty service is not covered for any problems caused by it.
• Data charges may apply when using features that use the Internet through mobile hotspots.

Description of the symbol

File:Icon warning.png	Warning : This sign warns that a risk of death or serious injury may result if caution is not taken.
File:Icon ban.png	Ban : This sign infoms you of action that should not be taken when using the product.
File:Icon caution.png	Caution : This sign inform you of the precautions to be taken for safe and correct use of the product.
File:Icon note.png	Note : This sign informs you of good information to know when using the product.

1.2 Precautions for the use environment

The temperature of the product may become excessively high in the following situations. High temperatures may cause product performance degradation, malfunction, or compromise safety.

• Do not store the product in extremely low or high temperatures.
• Do not expose the product to direct sunlight for a long time.
• Do not keep the product in a poorly ventilated room for a long time in the middle of the hot summer.
• Do not keep the product near appliances that may overheat, such as stoves and heating appliances.

1.3 Safety precautions

This is to protect the safety of users and others and prevent property damage in advance. Please read the following carefully before use and be sure to follow it.

File:Icon warning.png Warning
Failure to comply may result in death or serious injury.

Drive according to the actual laws.
Drive according to the marine indications and actual regulations when guiding a route using a GPS plotter.

The navigator should not keep an eye on the screen during the voyage.
It may cause a marine accident due to negligence in the front.

Do not mount the main in a place that interferes with vision or navigation.
Mounting it in a place that interferes with vision or safety may cause accidents at sea.

Install and wire correctly.
Failure to install and wire correctly according to the instruction manual may cause an accident or fire.

Do not disassemble, repair or remodel.
In case of failure, it may cause an accident or fire. If you disassemble, repair or remodel, you cannot receive A/S.

Do not use in a faulty or abnormal condition.
If it is used in an abnormal condition such as smoke or no sound, it may cause fire. Stop using it immediately and after checking the power supply , consult with the distributer you purchased .

This unit is for DC 12V to 36V only.
In case of using other volts , it may cause an accident or fire.

Use in a well-ventilated area.
If there is no ventilation, heat may be concentrated inside the main body and cause a fire.

Do not damage the wires and cords by pulling them.
It may cause a short circuit or disconnection, resulting in a fire or malfunction.

Do not drop it or subject it to strong impact.
It may cause malfunction or fire.

File:Icon caution.png Precaution
Failure to comply may result in personal injury or property damage.

Do not use for a long time with the engine stopped.
Sometimes the engine does not run due to battery drain.

Use a standard product when replacing the fuse.
Use of non-standard fudge may cause fire or malfunction. Use a 5A fuse.

For correct use
Handle it correctly according to the instructions.
Do not leave it in extreme high or low temperatures. (Storage temperature range: -10℃ ~ +50℃)

About LCD screen

• The screen looks different depending on the viewing angle. Use it within the range of the following angles. (Top 20º, Bottom 20º, Left 45º, Right 45º)
• The vision may deteriorate at temperatures below -10°C or above +50°C, but this is not a malfunction. It will recover within the preservation temperature range.
• When used in cold weather (below 0°C), the internal lighting divice (backlight) dims, but recovers when the temperature rises.
• Hitting the screen with a sharp object may cause damage.

1.4 Name and role of each part

1.4.1 Components

x110px

Main device

Error creating thumbnail: File missing

Protector

File:Component mount01.png

Mounting Bracket

File:Component gps antenna.png

External GPS ANT

File:Component power cable.png

Power Cable

File:Component remote control.png

Wireless R/C

File:Component fuse&bolt.png

Fuse & Bolt

File:Component knob01.png

Knobs

File:Component transducer.png

Transducer(600W) (CF only)

• Components may not be compatible with other devices.
• The appearance and specifications of components are subject to change without notice.
• For separately sold product, use the genuine products provided by Haiyang Olix and distributer. The use of nongenuine products can cause performance degradation and failure, and if a problem occurs, you cannot receive warranty service.

1.4.2 Each part name and key description

x27px x27px	It is used by setting the key the user wants.
x27px x27px	Chartplotter : Zoom in/out the map.
	Fishfinder : Adjusts the depth of water when it is manual.
File:Button vega arrow&rotary.png	Rotary: You can select a menu. You can set the ensitivity/attenuation when using the Fishfinder.
	Button : This is [Input] key.
File:Button vega menu ori.png File:Button vega goto ori.png	MENU : Invoke the menu.
	GOTO : It is used for temporary voyages.
File:Button vega page ori.png File:Button vega func ori.png	PAGE : Use to select a Screen mode.
	FUNC : It is used by setting the key the user wants.
File:Button vega mark ori.png File:Button vega track ori.png	WPT : Add/delete marks. Press for more than 3 seconds to set MOB.
	TRACK : Start/stop track recording.
File:Button vega cancel ori.png File:Button vega power ori.png	CANCEL : Use to cancel settings or exit menus.
	POWER : Power On/Off or Open the System Control window.

1.4.3 Connector specification

2-TD
File:Connector 2TD.png
NO	NAME
1	SPD_PULSE
2	SPD_VC
3	TD1
4	TD_GND
5	TD2
6	TEMP_VCC
7	TEMP_SIG
8	SPD_GND

3-TD
File:Connector 3TD.png
NO	NAME
1	UDI_TD 2
2	UDI_TD 1
3	UFF_TD 2
4	UFF_TD 1
5	TEMP_VCC
6	TEMP_SIG
7	TD_GND

NMEA 2000
File:Connector NMEA2000.png
NO	NAME
1	SHIELD
2	DC ±12V
3	DC -
4	CAN_H
5	CAN_L

POWER
File:Connector power.png
NO	NAME
1	DC +(12V~36V)
2	DC -
3	NC

NMEA 0183
File:Connector NMEA0183.png
NO	NAME
1	GND
2	TX +
3	GND
4	RX +
5	RX -
6	NC

AIS
File:Connector AIS.png
NO	NAME
1	GND
2	TX +
3	GND
4	RX +
5	RX -
6	NC

1.5 Memory card

Memory cards are used to store, restore, and back up various user data such as mark, route, track, set value and etc.
Vega support SD and micro SD.

1.5.1 Inserting memory card

Open the cover of the memory card slot and insert the memory card according to the hole. In the case of SD or microSD, insert it until it clicks.

1.5.2 Removing the memory card

For SD and microSD, first press once until you hear a click sound. It pops out slightly for easy removal. After, take it out lightly.

1.6 Turn on/off

1.6.1 Turn on

Press File:Button vega power.png lightly to turn on the product.

1.6.2 Turn off

1. Press File:Button vega power.png.
2. Press File:System power.png.
3. Press File:Button vega rotary.png or 'Yes' when a guide message appears.

1.7 Import previous device settings

You can import settings from your old device to your new device.

1. Insert the memory card into the old device.
2. File:Button vega menu.png → 8. Advanced → 5. Others → 1. Save User Setting to the memory card through Save User Settings.
3. Remove the memory card from your old device and insert it into your device.
4. From new product go to File:Button vega menu.png → 8. Advanced → 3. Maintenance → 7. Initialization → 1. User Initialization to Import old device's settings from memory card.

1.9 System Controls

You can make basic system settings. You can enter by pressing File:Button vega power.png.

File:System control.png

File:System power.png	Power off.
File:System restart.png	Restart the power.
File:System brightness.png	It can be adjusted by pressing File:Button vega left.png File:Button vega right.png or File:Button vega plus.png File:Button vega minus.png or turning File:Button vega rotary.png.
File:System night mode.png	Switch to night mode. night mode off night mode on
File:System touch lock.png	Disable the touch screen. Long touch when locking by touch.
File:System wifi.png	Enter the Wi-Fi setting window. Connect to the Internet through Wi-Fi before using the online update.
File:System bluetooth.png	Enter the Bluetooth setting window, Connect to the smart phone with Bluetooth before using the Pegasus.
File:System hy-net.png	Connect with VEGA-F using HY-NET.
File:System data overlay.png	Set the data layout bring the sailing information up freely on the desired location on the screen. Display All set layouts can be turned on or off in batches. EDIT You can turn on, move, or edit the following sailing information. GPS : Position, SOG, COG Time&Date : Time, Date Userdata Display : WPT, Track Fishfinder : Depth, Temp Weather : Weather, Wind Direction, Wind Speed, Temperatures, Water Temperature, Max Wind Speed, Wave Height, Max Wave Height, Wave Direction Unspecified : Voltage, HDG File:Vega data layout edit.png Display Turn the layout on or off. Size You can adjust the size of the layout. Color You can change the text color of the layout. Bezel When you turn on the border, a square border is formed around the layout.
40px	Display the desired weather information on the screen. One of the Weather, Wind Direction/Wind Speed, Wind Direction/Max Wind Direction, Temperatures, Water Temperature, Wave Direction/Wave Height, Wave Direction/Max Wave Height is displayed.

2 플로터

2.1 화면 설명

2.1.1 Cursor

Call

When using the main - Press x40px or touch the map screen. When using the remote control - Press [Cursor].

Moving

Keep pressing x40px or touch the desired location.

Deleting

When using the main - Press File:Button vega cancel.png when the cursor is called. When using the remote control - Press [Cursor] when the cursor is called. When using the touch - Press x40px at the top of the screen.

Cursor settings

In File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 8. Cursor, you can make settings related to the cursor.

1. Size : Adjust the size of cursor.
2. Magnetic : When you move the cursor around the mark, the cursor automatically moves to the center of the mark.
3. Extension Line : Add vertical and horizontal line from the cursor to end of the screen.
4. Vessel Line : Displays the line connecting the own ship and the cursor.
5. Move Cursor : Select whether to move the cursor at a constant speed or increase the speed of movement gradually when moving the cursor with the arrow keys.

2.1.2 Info window

You can set up information windows and subscreens in File:Button vega menu.png → 8. Advanced -> 2. Setup -> 6. Customizing -> 4. INFO Window.

1. WPT : Turn on/off the WPT information window.
2. Cursor : Turn on/off the cursor information window.
3. Position Setup : Set the location of the information window and sub screen.
4. SubScreen Size : You can adjust the inforamtion window and sub screen's size.

You can set the sub screen to be displayed at the bottom of the screen in File:Button vega menu.png → 8. Advanced → 5. Others → 2. SubScreen.

• Compass
• Depth/Temp
• SOG/COG
• Depth/Temp/SOG/COG
• GPS INFO1

2.2 Chartplotter settings

2.2.1 Map setup

File:Button vega menu.png → 8. Advanced → 6. Map Setup.

1. Map orientation
   You can set the plotter screen mode in File:Button vega menu.png → 8. Advanced → 6. Map Setup → 1. Map Orientation or by pressing x40pxon the upper right corner of the screen.
   • True Motion
     It is a sailing mode that the nautical chart is fixed and the onw ship moves. (True motion is not available for course-up and head-up.)
   • Up Mode
     It is a sailing mode that the own ship is fixed and the nautical chart moves. It can be used if a destination is entered. It is useful when you want to move the top of the screen is toward the destination or the own ship toward the destination.
2. Userdata Display : Setting up shown/hide the user data on the display.
3. Chart : Select the chart among HY-MAP, C-MAP and External map
4. C-MAP Setting (Only for C-MAP mode)
   • Chart Display Configuration : Set screens for Land, Marine, Depth, and Nav Addis on the map.
   • Chart Presentation : Sets the font, symbol size, and map color for the map.
   • Raster Setting : Sets the Raster mode on the map.
   • 3D View : Setup for 3D View.
   • Multi Language : Select language for name of the place, lighthouse or buoy.
   • Quick View : It is available to set up. Place the cursor on buoys or icons on the C-MAP, the information window is shown up automatically.
   • Touch : Sets the multi-touch features for the map.

2.2.2 Vessel

You can make settings related to own ship in File:Button vega menu.png → 8.Advanced → 7. Vessel.

1. Vessel Icon Size : Adjust size of own ship's icon.
2. Heading Line : Set the heading line's length. Heading line is used in true motion and north up mode.
3. Heading Line Thickness : Set the heading line's thickness.
4. Vessel Style : You can set own ship to one of Circle, Arrow and vessel.
5. Orient Resolution : If you set the heading angle, the map will not rotate according to the heading angle set in destination sailing or auto (head-up).

2.3 GPS settings

It is available to control and confirm information in GPS receiver.

2.3.1 Datum

It shows GPS Datum in File:Button vega menu.png → 8. Advanced → 1. GPS → 2. Datum. WGS-84, which is the worldwide standard is only available.

2.3.2 Fix correction

The coordinates received from the GPS receiver can be moved by the calibration value in File:Button vega menu.png → 8. Advanced → 1. GPS → 3. Fix Correction.

1. LAT Modification : You can calibration by moving the latitude north (N) or south (S).
2. LON Modification : You can calibration by moving the longitude west(W) or east (E).

2.3.3 Average Speed

It reduces unnecessary GPS deviation due to waves or currents. You can select settings according to the average ship speed at File:Button vega menu.png → 8. Advanced → 1. GPS → 4. Average Speed.

Average Speed Setup

You can adjust the setting value of the average Ship speed in File:Button vega menu.png → 8. Advanced → 1. GPS → 5. Average Speed Setup.

1. POG filtering : Used to smooth the position of the own ship. The lower setting value, the faster the response.
2. COG filtering : Used to smooth the azimuth of the own ship. The lower setting value, the faster the response.
3. SOG filtering : Used to smooth the Ship speed of the own ship. The lower setting value, the faster the response.
4. SOG Range : You can set the speed which applied average SOG. Average SOG is applied only under a speed be set.
5. COG : Select a different COG calculation method.
   • U Version : The COG's response is slow but stable. It is used a lot by low-speed fishing vessels.
   • C Virsion : The COG response is fast, but it may seem too sensitive. It's often used in fishing boats that require rapid response.

2.3.4 LAT/LON Unit

You can select the display unit of latitude/longitude from 3 units/4 units.

2.3.5 Receiving Port

Set GPS receiving port setting

2.4 WPT

Mark and record specific points on the nautical chart.

2.4.1 Creating WPT

1. Move desired location by calling cursor on the map.
2. Press File:Button vega mark.png to add a mark.

2.4.2 WPT List

In File:Button vega menu.png → 1. Userdata -> 1. WPT -> 1. List, you can check the list of created marks and edit, create, delete, sort and navigate.

Edit WPT

1. Press File:Button vega menu.png → 1. Userdata → 1. WPT → 1. List.
2. Select the WPT you want to edit from the WPT list.
3. Click [1.Edit] to edit the desired item.

WPT Sorting

1. Press File:Button vega menu.png → 1. Userdata → 1. WPT → 1. List.
2. Press [4.Sort] in the WPT list of WPT.
3. Select the desired sorting method.

Deleting WPT

1. Call the cursor on the map.
2. Move the cursor over the WPT you want to delete.
3. Press File:Button vega rotary.png and go WPT Cursor → 3. Erase, or Press File:Button vega mark.png to delete the WPT.

1. Press File:Button vega menu.png → 1. Userdata → 1. WPT → 1. List.
2. Select the WPT to delete from the WPT list.
3. Press [3.Delete] to delete the WPT.

Select/Delete All WPTs can be deleted entirely or only partially selected by shape or color.

1. Press File:Button vega menu.png → 1. Userdata → 1. WPT → 1. List.
2. Press [5. All Erase].
3. Select shapes and colors and press Delete.

File:Mark select delete window.png

Sailing

1. Press File:Button vega menu.png → 1. Userdata → 1. WPT → 1. List.
2. Select the WPT to navigate to from the WPT list.
3. Press [6. Goto].

1. Call the cursor on the map.
2. Move the cursor over a WPT to navigate.
3. Press File:Button vega rotary.png → WPT Cursor → 2. Goto.

2.4.3 Move the WPT

1. Call the cursor on the map.
2. Move the cursor over a WPT to move.
3. Press File:Button vega rotary.png → WPT Cursor → 4. Move..
4. Press File:Button vega rotary.png after moving the cursor to the desired location.

2.4.4 WPT setting

You can set the WPT to be created in the future. Press File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 5. Userdata → 1. WPT. .

• Symbol Setup
• Color Setup

2.4.5 WPT Select Area

You can select an area on the map and to delete or save the WPTs within it separately.

2.4.6 WPT display setting

You can set the display of WPTs on the electronic nautical chart in File:Button vega menu.png → 8. Advanced → 6. Map Setup → 2. Userdata Display → 1. WPT.

• WPT : Set whether to display WPTs on chart.

2.5 Route

The route shows the route by connecting the sailing points in order.

2.5.1 Route creating

1. Enter the route list via File:Button vega menu.png → 1. Userdata → 2. Route → 1. List.
2. Press [2. Add] on the route list.

2.5.2 Route list

You can check the list of created routes and edit, create, delete, sort, and voyage File:Button vega menu.png → 1. Userdata → 2. Route → 1. List.

Edit route

1. Select the rout to edit from the route list.
2. Press [1. Edit].

Deleting a route

1. Select route to delete in Route list.
2. Press [3. Erase]

Sort route

1. Press [5. Sort] in the Route list.
2. Select the desired sorting method.

Sailing by route

1. Select the route to sail in the Route list
2. Press [6. Goto]

2.5.3 Route display settings

File:Button vega menu.png → 8. Advanced → 6. Map Orientation → 2. Userdata Display You can set with regard to display.

4. Route : Set whether to display a route.
5. Route Name : Set whether to display route name next to route start point.

2.5.4 Navigation setting

You can operate and set marks during voyage in File:Button vega menu.png → 8. Advanced → 9. Navigation.

• Previous WPT : Change the WPT to sail in the route to previous WPT. Only available while sailing.
• Next WPT : Change the WPT to sail in the route to the next WPT. Only available while sailing.
• Route Order : You can set the route order. It can only be set while sailing.

2.5.5 Route detail

You can check and edit the destinations that make up the route. Press [4.Details] in the Route list.

Edit WPT
Select WPT to edit in the Route detail and press [1. Edit]. After that, edit the items you want.

Add WPT
There are two ways to add WPT.

Add saved WPT

1. In the Route detail, press [2.Saved WPT].
2. If you set the WPT name, you can call and add the WPT.

Add new WPT

1. Press [3.New WPT] in the Route detale.
2. It is added as the position of the own ship just below the currently selected WPT. For detailed settings, Edit [1. Edit]

Deleting WPT
Select the WPT to delete and press [4. Erase].

Finding WPT location
Select the WPT to find and press [5. Find].

2.6 Goto

There is two type of Goto method. You can select from File:Button vega menu.png → 8. Advanced -> 9. Navigation -> 5. Goto Type.

Type1

This is a method of using a temporary destination and a temporary route together.

1. Designate destination to go by cursor.
2. Press File:Button vega goto.png and set the destination.
3. Set the next destination in the same way.
4. When you have set as many routes as you want, press File:Button vega rotary.png to proceed with the goto.
5. To finish the goto, press File:Button vega rotary.png without the cursor or touch the exit at the bottom of the screen.

Type2

This is for temporary destinations only.

1. Designate destination to go by cursor.
2. Press File:Button vega goto.png and set the destination.
3. To change the destination, designate the new destination by cursor and press File:Button vega goto.png.
4. To finish the voyage, press File:Button vega goto.png without the cursor or touch the exit at the bottom of the screen.

2.7 Track

Draws the wake line that the own ship has sailed.

2.7.1 Turn on/off drawing track

You can turn on or off the drawing of the track by pressing File:Button vega track.png.

2.7.2 Set how to draw a wake

You can set whether you to draw track at regular time intervals or at reqular distance in File:Button vega track.png → 1. Userdata → 3. Track → 2. Setup → 2. Record Setup.

Draw every time interval

Draws a track at regular intervals. Time interval can be set in File:Button vega menu.png → 1. Userdata → 3. Track → 2. Setup → 3. Time Interval.

Draw every distance interval

Draws a track at regular distances. Distance interval can be set in File:Button vega menu.png → 1. Userdata -> 3. Track -> 2. Setup -> 4. DIST Interval.

2.7.3 Track color settings

Select the desired color from File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 5. Userdata → 2. Track → 1. Color Setup and press File:Button vega rotary.png. Template:Note

2.7.4 Set the thickness of the track line

You can change the thickness of the track line in File:Button vega menu.png → 1. Userdata → 3. Track → 2. Setup → 1. Tickness.

2.7.5 Track management

Tracks can be saved up to a total of 50,000 points. There are two types of track management. Track type can be changed in File:Button vega menu.png → 1. Userdata → 3. Track → 2. Setup → 5. Track Type.

Type 1

Manage all tracks with color at once.

Deleting a track

You can delete a track in File:Button vega menu.png → 1. Userdata → 3. Track → 1. Erase.

• To delete only a specific color, select the desired color and press File:Button vega rotary.png.
• Press File:Button vega menu.png to delete all.
• To delete only a specific section from the map, press [2.Partial].
  

File:Track delete partial.png
Designate the beginning of the track to delete by long-touching or pressing Input.
The end is specified in the same way. If you select “Yes” in the window asking for deletion, the specified number of tracks will be deleted.

Type2

Tracks are managed in 5 indexes. You can draw 10,000 tracks for each index.

Index selection

You can select index to manage in File:Button vega menu.png → 1. Userdata → 3. Track → 1. Select Index.

List

Enter File:Button vega menu.png → 1. Userdata -> 3. Track -> 3. List.

Delete

Select the desired index from the track list and press [2.Erase].

2.7.6 Select Area

You can specify an area on the map and save or delete tracks in it separately.

1. Press File:Button vega menu.png → 1. Userdata -> 3. Track -> 3. Select Area.
2. Move the cursor to the point where you want to start specifying the area.
3. Press Input or [1.Select Area].
4. Move the cursor to the point where you want to finish specifying the area.
5. Press Input or [2.Select Complete].
   • When deleting a track
     6. Press [1. Erase]
     7. Select the track color to delete and press Erase.
   • When saving a track
     6. Press [2. Save].
     7. Select the save location.
     8. Specify a file name.
     9. Select the track color to save and press Save.

2.8 Measuring distance/direction

The distance and bearing between two points user wants can be measured.

1. Call the cursor and move to the first point.
2. Press File:Button vega rotary.png → Function → 8. Range/BRG..
3. Move the cursor to the second point.
4. Check the distance and bearing of the two points in the cursor information window at the lower left.
5. Press File:Button vega cancel.png to exit.

2.9 User line

Users can draw lines on the map arbitrarily.

2.9.1 User line drawing

1. Call the cursor.
2. Press File:Button vega rotery.png → Function → 9. User Line.

Move the cursor to the starting position and press File:Button vega rotery.png를 누르세요.

1. Continue to draw a line by pressing File:Button vega rotery.png at the desired point.
2. After drawing, press File:Button vega cancel.png to exit.

2.9.2 User line list

You can check, edit, and delete the user line list in File:Button vega menu.png → 1. Userdata → 4. User Line → 1. List.

2.9.3 Edit user line

1. Select the user line to edit from the user line list.
2. Press [1. Edit] to edit the desired item.

2.9.4 User line Delete/all delete

1. Select the user line to delete from the user line list.
2. Press [2.Erase] to delete.
3. Press [All Erase] to delete all.

2.9.5 User line display setting

You can set whether to display the user line on the electronic nautical chart in File:Button vega menu.png → 8. Advanced → 6. Map Setup → 2. Userdata Display → 7. User Line.

2.10 User name

User can input the place name that is not on the map manually.

1. Call the cursor.
2. Move the cursor to the place to input the name.
3. File:Button vega rotary.png → Fucntion → 10. User Name.
4. Set the place name and color.
5. Press Cancel to exit.

2.10.1 User name display setting

You can set whether to display the user line on the electronic nautical chart in File:Button vega menu.png → 8. Advanced → 6. Map Setup → 2. Userdata Display → 8. User Name.

2.10.2 User line alarm setting

You can set the boundary line alarm sound in File:Button vega menu.png → 8. Advanced → 8. Alarm → 4. User Line..

• User Line Alarm : The alarm sounds if the boundary set by the user violated. It sounds only user line set by alarm method.
• User Line Range : Set the range to recognize that the user's boundary has been violated during sailing.

2.11 Other setting

2.11.1 Unit setting

Set the units for distance and speed in File:Button vega menu.png → 8. Advanced -> 2. Setup -> 1. Unit.

1. DIST/Speed
   1NM = 1.852km
   1kt=1.852km/h
2. Depth
   1m = 3.281ft = 0.549fm = 0.609lfm = 0.660Jfm
3. TEMP
   Celsius℃ = Fahrenheit +32℉

2.11.2 Compass

File:Button vega menu.png → 8. Advanced → 2. Setup → 2. Compass

1. BRG
   There is a difference degree where you are in the earth. This function is to modify the error from true and Magnetic.
2. Fix Correction
   When using a compass as a magnetic north, there are errors in each region, so use it by correcting the value.
3. External Compass
4. External Compass Smoothing
   It is a function that softens the movement of the map when using an external compass.

2.11.3 Time&Date Setting

File:Button vega menu.png → 8. Advanced → 2. Setup → 3. Time&Date

1. Reference
   The GPS receiver uses the international standard time, the time zone may vary by region (country).The display time can be adjusted when sailing in different time zone
2. Time Format
   You can set the time display method.
3. Date Format
   You can set the date display order to year-month-day, month-day-year, day-month-year.
4. Month Format
   You can set the date format to either letters or numbers.

2.11.4 Input-output setting

File:Button vega menu.png → 8. Advanced → 2. Setup → 4. Input/Output

1. Output Sentences

DESCRIPTIONS	CONTENTS OF DATA FIELD	DEFAULT
$GPGGA	GPS information	ON
$GPVTG	Ship speed and direction inforamtion	ON
$GPZDA	Time and Date	OFF
$GPRMB	Recommended minimum voyage information	OFF
$GPRMC	GNSS information	ON
$GPAPB	Heading/track controller (autopliot) sentence B	ON
$GPXTE	Cross-track error, measured	OFF
$GPBOD	Bearing, origin to destination	OFF
$GPBWC	Waypoint direction and distance	ON
$SYPLT	삼영 자동 조정 장치	OFF

2. Transmit
   You can set the NMEA and AIS transmission speed.
3. Output Version
   You can set the Output Version.

2.11.5 Menu setting

You can set menu related settings in File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 3. Menu.

1. Type : You can choose Smart method, HGP method and Touch method.
2. Color : You can change the color of the menu to the color you want.

2.11.6 Selection method

You can set menu related settings in File:Button vega menu.png → 8. Advanced -> 2. Setup -> 6. Customizing -> 5. Userdata -> 3. Selection Method.

• Standard : You can view and select Shapes, colors, images.
• Flip : You can select by sliding shapes and colors sequentially.

2.11.7 Total distance reset

You can reset the data bar, navigation data screen, compass screen, highway screen, and GPS information screen to 0 in File:Button vega menu.png → 8. Advanced -> 2. Setup -> 6. Customizing -> 5. Userdata -> 4. Total Distance Reset.

2.11.8 Password

You can set password related settings in File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 5. Userdata.

5. Use Password : You can set whether to use a password or not. If you use a password, you need to turn on the product and enter the password to use the product.
6. Set Password : You can set a 6-digit password.
7. Reset Password : Resets the password. You must enter the set password.

2.11.9 Transparency

In File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 6. Alpha Blending, you can set the background transparency of the data bar and sub screen. (The lower the number, the more transparent it is.)

2.11.10 Auto back up

When File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 9. User Convenience → 1. Auto Backup is turn on, WPTs and tracks are automatically backed up internally. File name is saved as mark WPT_backup.dat and track TRACK_backup.dat.

2.11.11 Auto night mode

If you change the night mode to ON in File:Button vega menu.png → 8. Advanced → 2. Setup → 6. Customizing → 9. User Convenience → 3. Auto Night Mode, the night mode automatically turns on at the set start time and turns off at the end time.

2.11.12 Equipment initialization

You can initialize in File:Button vega menu.png → 8. Advanced → 3. Maintenance → 7. Initialization.

1. User Initialization : It is initialized to the settings saved by the user.
2. Setup Initialization : All set values ​​are initialized to the initial state.
3. Factory initialization : All set values and user datars are initialized to the initial state.

2.11.13 Buzzer setting

You can turn on and off the action sound in File:Button vega menu.png → 8. Advanced → 2. Setup → 5. Buzzer.

2.11.14 Check the version

You can check the version in File:Button vega menu.png → 8. Advanced → 3. Maintenance.

1. Program Version
2. OS Version
3. Map Version

2.11.15 Simulator

In File:Button vega menu.png → 8. Advanced → 3. Maintenance → 4. Simulator, you can test start the following functions with the data stored in the memory.

1. GPS
2. Fishfinder
3. AIS

2.11.16 Remote control settings

You can settings related to the remote control in File:Button vega menu.png → 8. Advanced -> 3. Maintenance -> 6. Remote Control Settings.

1. Remote Control : You can set whether to use the remote control.
2. Remote Control Pairing : You can register the remote control to use with this product. When the remote control registration window appears and then press the Cancel button on the remote control twice, Remote control is registered. When a remote control is registered, operation is possible only with the remote control.
3. Remote Control Dispairing : Unregister the remote control and receive operation signal from all remote control.

2.11.17 Wired LAN setting

You can set IP of wired LAN in File:Button vega menu.png → 8. Advanced → 3. Maintenance → 8. Wire LAN.

2.11.18 Online update

Programs and maps can be updated to the latest version through the Internet.

핫스팟 켜기

온라인 업데이트에는 인터넷 연결이 필요합니다. 스마트폰의 핫스팟 기능을 켜주세요.

핫스팟은 스마트폰을 통해 무선인터넷을 공급하기 위한 기능으로, Wi-Fi 무선 인터넷이 공급되는 장소라면 해당 과정은 생략하셔도 됩니다.

스마트폰 마다 메뉴 형태나 구성이 다를 수 있습니다. 핫스팟 이름을 반드시 기억해주시고, 비밀번호를 설정할 경우 비밀번호도 기억해주세요. (기능 사용에 익숙하지 않은 경우 비밀번호는 해제하는 것을 권장합니다.) 사용하시는 요금제에 따라 데이터 요금이 부과될 수 있습니다.

와이파이 연결

온라인 업데이트 중에는 스텔라를 와이파이 무선 인터넷 공급원에 가까이 두세요. 핫스팟을 켜놓은 스마트폰을 멀리 가져가는 등의 행동은 온라인 업데이트에 지장을 줄 수 있습니다.

프로그램, 지도, 기타 업데이트

위 예시에서 다운로드, 설치 속도는 설명을 위해 빠르게 표현한 것으로, 실제로는 다소 시간이 소요됩니다. 예시와 다르게 속도가 느리다고 하더라도 정상이오니 불필요하고 무리한 조작을 하지 마시기 바랍니다.

업데이트를 완료한 후, 스텔라의 와이파이를 꺼주세요. 특히 스마트폰의 핫스팟은 반드시 꺼주세요. 핫스팟이 켜져있을 경우 배터리 소모량을 늘리고, 불필요한 데이터 요금이 부과될 수 있습니다.

2.11.19 Language and Input

You can set Android system languages and keyboards on File:Button vega menu.png → 8. Advanced → 3. Maintenance → 10. Advanced Menu → 1. Language & Input.

2.11.20 Anchor alarm settings

You can set anchor alarm in File:Button vega menu.png → 8. Advanced → 8. Alarm → 2. Anchor.

1. Anchor Alarm : If ship leave the anchor Radius during the docking, device will sound an alarm.
2. Anchor Radius : Sets the range that recognizes that the ship being docked is out of the dock.

2.11.21 Interval alarm setting

You can set alarm that sounds at regular time intervals in File:Button vega menu.png → 8. Advanced → 8. Alarm → 3. Interval.

1. Interval Alarm : Turn on and off the time alarm.
2. Interval Time : Set the time interval to sound the alarm from 1 to 60 minutes.

2.11.22 Calendar

You can check date and tide information on File:Button vega menu.png → 8. Advanced → 4. Calendar.

2.11.23 Screen capture

Capture the entire current screen as an image through File:Button vega menu.png → 8. Advanced → 5. Others → 3. Screen Capture. Capture file saved in memory can be checked or deleted from File:Button vega menu.png → 8. Advanced → 5. Others → 4. Capture List. Template:Caution

3 Fishfinder

3.1 Screen description

3.1.1 Mode

You can set the screen mode in File:Button vega menu.png → 5. Mode. It supports two frequencies both 50kHz and 200kHz.

Normal mode and dual mode Depending on the screen mode setting, only one frequency can be displayed on the screen or both frequencies can be displayed on the screen at the same time.

Various mode

3.2 Data bar (Fishfinder)

This is a dedicated data bar of Fishfinder.

File:Databar fishfinder.png

3.2.1 Adjusting the depth of water.

1. Press File:Button vega left.png File:Button vega right.png to select the depth of water.
2. Turn File:Button vega rotary.png to adjust the depth of water.

3.2.2 Auto/Manual depth range

You can change the depth of the water automatically or manually from File:Button vega menu.png → 2. Depth Range.

3.2.3 Depth of water shift

Raise the lowest depth of water as you want and display it on the screen. You can set in File:Button vega menu.png → 4. Shift. Template:Caution

3.2.4 Adjusting the Sensitivitiy

1. Press x60px to select the sensitivity of frequency. You can see that the frequency has been selected through the blue text background.
2. Turn File:Button vega rotary.png to adjust the sensitivity.

3.2.5 Adjusting the attenuation (STC)

1. Select attenunation (STC) of frequency by pressing 60px.
2. Adjust the attenuation (STC) by turning File:Button vega rotary.png.

3.3 VRM

Measure accurate depth of water for Fish, object and nature. Press File:Button vega mark.png to call the green depth of water bar.

1. Move the depth of water bar up down using the cursor.
2. Check the depth of water through number on the Depth of water bar.

가운데

3.4 타임머신

파일:버튼 베가 메뉴.png → 6. 어군탐지기 -> 9. 타임머신을 Off으로 하면 지나간 어군탐지기의 화면을 보고 싶을 때, 되돌려 볼 수 있습니다.

1. 어군탐지기를 활성화 한 상태에서 리모컨의 [커서]키를 누르세요.
2. 커서가 호출되면 파일:버튼 베가 좌.png 파일:버튼 베가 우.png키를 누르거나 파일:버튼 베가 로터리.png를 돌리거나 또는 터치를 이용해 지나간 어군탐지기 화면으로 이동해 확인하세요.

어군탐지기의 지나간 화면에서 파일:버튼 베가 마크(mob).png를 누르면 과거의 위치에 빨간 선과 함께 마크가 입력됩니다. 상황에 따라서 생성되는 마크의 오차 범위는 다릅니다.

타임머신으로 확인할 수 있는 화면의 길이는 수심에 따라 다릅니다.

3.5 화면 설정

3.5.1 이미지 속도

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 3. 화면 설정 → 2. 이미지 속도에서 1/32X~4X 까지 어군탐지기 화면의 이동 속도를 선택할 수 있습니다.

3.5.2 화이트 라인

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 2. 화면 설정 → 3. 화이트 라인에서 해저 표면의 색상을 변경하여, 어군과 해저를 보다 명확하게 구분해줍니다. 검정색과 흰색으로 변경할 수 있습니다.

3.5.3 물고기 심볼

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 2. 화면 설정 → 9. 어탐 기타기능에서 어탐화면 위에 어군이 탐지됐을 때 어군 위에 물고기 심볼 표시에 관한 설정을 할 수 있습니다.

1. 물고기 심볼 : 물고기 심볼을 켜고 끕니다.
   파일:물고기 심볼.png
2. 물고기 사이즈 : 어군의 사이즈 표시를 켜고 끕니다. cm 혹은 inch로 표시할 수 있습니다.
   파일:물고기 사이즈.png

바다 환경에 따라 어군판별이 정확하지 않을 수 있습니다. 바다 환경에 따라 어군 사이즈가 정확하지 않을 수 있습니다.

3.6 기타 설정

3.6.1 타선박 간섭 제거

다른 선박의 어탐에 영향을 받아 발생하는 간섭을 제거합니다. 가까운 거리에서, 어탐을 장착한 다른 선박과 조업할 때 이용합니다. 파일:버튼 베가 메뉴.png → 4. 제거설정 → 1. 타선박 간섭제거에서 켜고 끌 수 있습니다.

3.6.2 색상 소거

낮은 레벨의 색상부터 차례로 화면에서 지웁니다. 어탐 화면에 노이즈(잡음)가 많이 표시될 경우나 강한 반사판만 보고 싶을 경우 사용하세요. 파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 5. 색상설정 → 1. 색상 소거에서 설정할 수 있습니다.

3.6.3 화면 색상 선택

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 5. 색상설정 → 3. 어탐화면 색상선택에서 어탐 화면의 바탕색을 변경할 수 있습니다.

3.6.4 이미지 필터

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 5. 색상설정 → 3. 이미지 필터에서 가로, 세로 이미지 필터를 켜고 끌 수 있습니다.

3.6.5 펄스폭

파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 9. 기타 → 1. 펄스폭에서 어탐 송신부의 송신 펄스 폭을 변경합니다.

펄스폭을 좁게 하면, 어군 판별이 좋고 수심 판별은 떨어집니다. 반대로 펄스폭을 넓게 하면, 수심 판별은 좋아지고 어군 판별은 떨어집니다.

3.6.6 수온 보정

수온이 정확하지 않을 때 파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 9. 기타 → 2. 수온 보정에서 보정할 수 있습니다.

3.6.7 선속 보정

선속이 맞지 않을 때 파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 9. 기타 → 3. 선속 보정에서 보정할 수 있습니다.

선속입력 설정이 송수파기일 경우에만 사용 가능합니다.

3.6.8 송수파기 위치 보정

배의 송수파기 위치가 수면과 차이가 있을 때 파일:버튼 베가 메뉴.png → 6. 어군탐지기 → 9. 기타 → 4. 송수파기 위치에서 보정할 수 있습니다.

3.6.9 선속입력 설정

파일:버튼 베가 메뉴.png → 6. 어군탐지기 -> 9. 기타 -> 5. 선속입력 설정에서 어느 선속 정보를 입력 받을지 선택합니다.

• 송수파기 : 송수파기에 설치된 선속 센서로 표시합니다.
• GPS : GPS로 들어오는 선속을 표시합니다.

4 AIS

4.1 AIS란?

AIS(Automatic Identification System)는 선박과 선박 간, 선박과 육상국 간의 충돌사고 방지를 위한 운항정보 또는 항만보고를 위한 정보를 주기적으로 교환하도록 하는 시스템입니다. AIS는 선박의 제원, 운항정보를 정해진 시간에 따라 송신을 하여 타 선박과의 정보 공유로 안전한 운행을 할 수 있도록 하는 항해 장비입니다.

4.1.1 AIS 시스템 정보

CPA	Closest Point of Approach의 약자로 자신의 자선과 타선박의 거리를 의미합니다.
TCPA	Time to Closest Point of Approach의 약자로 자신의 자선과 타선박의 충돌 예상시간을 의미합니다. 충돌예상은 자선과 타선박의 선속, 방위 등을 고려하여 예상합니다.
선명	배의 이름을 의미합니다. 선명은 최대길이가 20자입니다.
MMSI	Maritime Mobile Service Identity의 약자로 배마다 고유번호를 의미합니다.
MMSI 번호	9자리의 숫자로 구성돼있습니다. 이 번호는 선박마다 다른 식별번호입니다.
타겟 파일:아이콘 AIS 타겟.png	화면상의 타 선박을 의미합니다.
활성화된 타겟 파일:아이콘 AIS 활성화된 타겟.png	타겟의 정보가 주기적으로 갱신되는 타겟을 의미합니다.
선택된 타겟 파일:아이콘 AIS 선택된 타겟.png	커서로 선택한 AIS 타겟의 정보창을 볼 수 있습니다.
위험한 타겟 파일:아이콘 AIS 위험한 타겟.png	CPA 알람이나 TCPA 알람에서 체크된 타겟을 의미합니다. 사용자가 설정한 위험한 타겟입니다. 타겟의 색상이 빨간색으로 표시됩니다.
오래된 타겟 파일:아이콘 AIS 오래된 타겟.png	사용자가 정의한 시간 안에 갱신되지 않은 타겟을 의미합니다. 타겟에 X가 표시됩니다.

4.2 AIS 켜고 끄기

파일:버튼 베가 메뉴.png → 8. AIS → 1. AIS On/Off에서 AIS기능을 켜거나 끌 수 있습니다.

4.3 AIS 정보창

원하는 타겟을 터치하거나 커서를 놓고 파일:버튼 베가 로터리.png를 누르면 해당 타겟의 AIS 정보창을 보여줍니다. {{알림|파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 2. 타겟정보보기에서 AIS 정보창에 표시할 항목을 설정할 수 있습니다.

타겟정보표시 AIS 타겟 밑에 최대 4개까지 원하는 정보를 표시할 수 있습니다.

• 파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 1. 타겟정보표시에서 원하는 항목을 ON으로 합니다.
• AIS 정보창에서 원하는 항목을 선택해줍니다.

AIS 정보창에서 실수로 타겟정보표시 항목을 변경되지 않도록 잠그려면 파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 1. 타겟정보표시 → 1. 팝업 선택을 ON으로 설정하세요.

4.4 AIS 목록

파일:버튼 베가 메뉴.png → 8. AIS → 2. 목록에서 AIS타겟의 목록을 볼 수 있습니다.

세부사항

원하는 AIS 타겟을 선택 후 파일:버튼 베가 로터리.png 또는 [1.상세보기]를 누르거나, AIS 타겟을 터치하면 상세한 정보를 볼 수 있습니다. 가운데

4.5 기타 설정

4.5.1 AIS 거리원

파일:버튼 베가 메뉴.png → 8. AIS → 3. AIS 거리원을 켜면 자선을 중심으로 거리를 측정할 수 있는 동심원을 그려 수신된 AIS들의 거리를 가늠할 수 있습니다. 400px|가운데

4.5.2 AIS 크기

파일:버튼 베가 메뉴.png → 8. AIS → 4. AIS 크기에서 AIS 타겟의 크기를 조절할 수 있습니다.

4.5.3 국가별 심볼 색상 설정

파일:버튼 베가 메뉴.png → 8. AIS → 5. 국가별 설정에서 기본 색상 및 MMSI의 국가 번호별로 심볼의 색상을 설정할 수 있습니다.

4.5.4 타겟 종류별 모양

파일:버튼 베가 메뉴.png → 8. AIS → 6. 타겟종류별 모양에서 AIS 타겟 종류에 따라 아이콘 모양을 설정할 수 있습니다.

4.5.5 타겟종류 ON/OFF

파일:버튼 베가 메뉴.png → 8. AIS → 7. 타겟종류 ON/OFF에서 타겟종류에 따라 화면 표시 여부를 설정할 수 있습니다.

4.5.6 수신 지연 시간 설정

파일:버튼 베가 메뉴.png → 8. AIS → 8. AIS 타겟설정 → 1. 수신지연 설정시간에서 설정한 시간 만큼 수신이 안된 타겟에는 'X'를 표시합니다.

4.5.7 타겟제거 설정시간

파일:버튼 베가 메뉴.png → 8. AIS → 8. AIS 타겟설정 → 2. 타겟제거 설정시간에서 설정한 시간 만큼 AIS 타겟의 정보가 갱신되지 않은 타겟은 화면에서 지워집니다.

4.5.8 자선타겟

파일:버튼 베가 메뉴.png → 8. AIS → 8. AIS 타겟설정 → 3. 자선타겟에서 자선의 AIS타겟을 화면에 표시할지 설정할 수 있습니다.

4.5.9 SART 메시지

파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 3. 테스트 메세지 보기를 ON으로 하면 SART 메세지 중에서 테스트로 수신된 메세지를 볼 수 있습니다.

4.5.10 AIS 스케일

파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 5. AIS 스케일에서 설정한 축척 이하에서만 AIS 타겟이 지도에 표시됩니다.

4.5.11 선박명

파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 5. 지도 선박명 선택에서 해도에 표시되는 선박명을 표기하는 방식을 선택할 수 있습니다.

4.5.12 정보 외곽선

파일:버튼 베가 메뉴.png → 8. AIS → 9. 기타 → 7. 정보 외곽선을 켜면 해도에 표시 되는 AIS 타겟 정보가 배경과 혼동되지 않고 또렷이 잘 보이도록 외곽선을 만들어줍니다.